日本h番全彩无遮挡h工口-国产精品无码无片在线观看3d-四虎国产成人永久精品免费-广东少妇大战黑人34厘米视频-人人妻人人狠人人爽天天综合网

當前位置:首頁-新聞資訊

鋁板幕墻材料如何進行選擇使用?

來源:http://www.kangyanghua.com/ 發布時間:2018-04-16

①使用年限在十年內時宜采用鋁塑板,原因是現在的鋁塑板良莠不齊,魚目混珠,加之考慮施工時需現場加工,內外表面的鋁箔只有0.5mm許多廠家的鋁塑板是采用輥涂工藝進行表面處理的,表面有一定的紋理,因此設計人員在進行材料使用率優化時要注意不可將板面橫豎亂放,影響效果按照規范要求.
(1) the use of aluminum plastic plate in ten years, the reason is that the present aluminum and plastic plates are good and bad, mixed with fish and eyes, and the construction needs to be processed in the field. The aluminum foil on the inside and outside surface is only 0.5mm many manufacturers of aluminum plastic plate surface treatment with roll coating process, with a certain texture on the surface, so the designers are in the process. For the utilization of materials to optimize attention will not be the board anyway misplacing effect in accordance with the specification requirements.
鋁塑板的邊部需加強,可采用鋁方管或角鋁等固定,粘接膠宜采用中性硅酮結構膠當鋁塑板安裝部位在建筑物的防火區間或靠近該區時,應采用防火型鋁塑板當鋁塑板設計尺寸較大時,需進行加強肋的結構計算以確定肋的規格和分布間距固定鋁塑板和龍骨的耳板多采用角鋁,角鋁的長度不宜小于50mm,角鋁在龍骨一邊上宜開長孔,保證板面的熱脹冷縮。設計人員還需注意不要在易破壞部位使用鋁塑板,否則需在背面做加固處理。
The edge of the aluminum plastic plate should be strengthened, the aluminum square tube or the angle aluminum can be fixed, and the adhesive is suitable for the use of neutral silicone structural adhesive when the installation part of the aluminum plastic plate is in the fire zone of the building or near the area. When the design size of the aluminum plastic plate is large, the structure of the stiffened ribs should be calculated to determine the size of the ribs. The length of the ear plate of the fixed aluminum plastic plate and the keel is mostly used with angular aluminum, the length of the angular aluminum should not be less than 50mm, and the angular aluminum should open the long hole on the side of the keel, so that the heat expansion and contraction of the plate surface can be ensured. Designers also need to be careful not to use aluminum plastic panels at vulnerable locations, otherwise they need to be reinforced on the back.

鋁卷生產廠家
②使用年限在十年以上時宜采用鋁單板。鋁單板強度好,耐腐蝕性強,在工廠加工能保證質量。由于施工現場所要鋁單板是在工廠加工成成品,直接安裝即可,所以設計人員在做鋁單板加工圖時需注明鋁單板的材質、厚度、固定耳板規格和加工尺寸及分布間距、加工誤差要求、加強肋的規格和分布間距等。需要注意的是耳板靠近龍骨一側的固定孔的加工尺寸要考慮熱脹冷縮,一般在耳板上開長圓孔,固定螺釘時要盡量將螺釘固定在長圓孔的中部,這樣即方便安裝又可有伸縮性,同時要注意板四周的耳板要錯位固定,否則在安裝時可能“打架”鋁單板表面宜采用氟碳噴涂(氟碳樹脂的各項性能都較其他處理方式優越),盡量避免采用輥涂方式(有的加工廠的輥涂產品有方向性,影響外觀效果)。
Second, when the service life is over ten years, the aluminum panel should be used. Aluminum sheet has good strength and strong corrosion resistance. It can ensure quality in factory processing. As the aluminum sheet of the construction site is processed into finished product in the factory, it can be directly installed, so the designer should indicate the material, thickness, fixed ear plate specification and machining dimensions and distribution spacing, processing error requirements, strengthening rib gauge and distribution spacing when making aluminum sheet processing drawings. It is important to note that the machining dimension of the fixed hole near the side of the keel should consider the heat expansion and contraction, the long circular hole is generally opened on the ear plate, and the screw should be fixed to the middle of the long circular hole as far as possible, so that it is convenient to install and can be retracted, at the same time, it should be noted that the ear plate around the plate should be staggered and fixed, otherwise the installation should be installed. It is possible to use fluorocarbon spray on the surface of the "fight" aluminum sheet (the performance of fluorocarbon resin is superior to other treatment methods), and the way of roll coating is avoided as far as possible (the roll coating of some processing plants is directional and affects the appearance effect).
現在有很多建筑采用穿孔鋁單板以豐富效果,如果穿孔鋁單板后面沒有防水隔離層,那就可在實體墻外表面做防水層或作雙層幕墻或直接在穿孔鋁單板背面做防水隔離層,然后再設計穿孔鋁單板。鋁單板的孔洞尺寸必須大于板厚(工藝要求),孔間距及尺寸要依據材質的強度要求(純鋁單板較合金鋁單板強度低),同時考慮加強肋的安裝,避免影響外視效果。合理的設計是先做樣板,通過遠觀和近看確定孔尺寸及間距。
Many buildings now use perforated aluminum sheet to enrich the effect. If there is no waterproof isolation layer behind the perforated aluminum sheet, the waterproof layer or double curtain wall can be made on the outer surface of the solid wall or the waterproof isolation layer directly on the back of the perforated aluminum sheet, and then the perforated aluminum sheet can be redesigned. The pore size of the aluminum sheet must be larger than the thickness of the plate (process requirements). The distance and size of the hole should be based on the strength requirements of the material (the strength of the pure aluminum sheet is lower than that of the alloyed aluminum sheet). At the same time, the installation of the ribs should be strengthened to avoid the effect of the external sight. The reasonable design is to make the template first, and determine the hole size and distance through the far and near view.
有了鋁卷生產廠家上面的小總結,希望對廣大客戶有所幫助,如果有什么不理解的或者尋求幫助的請點擊我們的官方網站:http://www.kangyanghua.com者來電咨詢,我們會盡全力為您解決
We have a small summary of the aluminum producers, hoping to help the customers. If there is anything that is not understood or ask for help, please click on our official website: http://www.kangyanghua.com caller calls, we will do our best to solve the problem.

主站蜘蛛池模板: 日韩av午夜在线观看| 无码精品a∨在线观看十八禁| 天堂在线资源中文在线8| 成在人线av无码免费高潮喷水| 亚洲av永久无码精品放毛片| 欧美成人秋霞久久aa片| 久久久久亚洲av无码专区网站| 国产成人精品久久一区二区三区 | 亚洲s码欧洲m码吹潮| 国产成+人+综合+亚洲欧美丁香花| 久久影院午夜理论片无码| 亚洲精品无码永久在线观看你懂的 | 丰满人妻熟妇乱又伦精品软件| 成年女人免费v片| 一进一出xo动态图| 无码视频一区二区三区| 国产大屁股喷水视频在线观看| 国产成人无码网站| 国产欧美亚洲精品a| 一二三四视频社区在线| 99精产国品一二三产品香蕉| 国产在线观看免费视频软件| 国产精品va在线观看无码不卡| 国产良妇出轨视频在线观看| 欧美日韩国产精品自在自线| 亚洲七久久之综合七久久| 欧美丰满熟妇乱xxxxx网站| 亚洲中文字幕久久精品无码a| 久久精品无码一区二区三区| 欲色天天网综合久久| 国产精品久久久久9999赢消| 亚洲成色在线综合网站免费| 国产精品沙发午睡系列990531| 97精品人妻一区二区三区香蕉| 欧美xxxxx高潮喷水| 精品久久香蕉国产线看观看亚洲| 久久精品aⅴ无码中文字字幕不卡| 国产成人精品aa毛片| 国内精品久久人妻互换| 中国大陆高清aⅴ毛片| 蜜桃日本免费观看mv|