日本h番全彩无遮挡h工口-国产精品无码无片在线观看3d-四虎国产成人永久精品免费-广东少妇大战黑人34厘米视频-人人妻人人狠人人爽天天综合网

當前位置:首頁-新聞資訊

鋁板擠壓表面起皮起泡怎么消除?

來源:http://www.kangyanghua.com/ 發布時間:2018-07-19

一、鋁板擠壓產生氣泡、起皮的原因
1. The reasons for the extrusion of aluminum plates to produce bubbles and peels
擠壓筒、擠壓墊磨損超差,擠壓筒和擠壓墊尺寸配合不當,使用的墊片直徑差超過允許值;
The diameter of the gasket is higher than the allowable value because of the improper wear and tear of the extrusion cylinder, the extrusion pad and the improper size of the extrusion cylinder and the extrusion pad.
擠壓筒和擠壓墊太臟,粘有油污、水分、石墨等;
The extrusion cylinder and the extrusion pad are dirty, sticky with oil, moisture, graphite, etc.
潤滑油中含有水;
The lubricating oil contains water.
鑄錠表面鏟槽太多,過深,或鑄錠表面有氣孔、砂眼,組織疏松、有油污等;
The surface of the ingot is too much, too deep, or the surface of the ingot has holes and sand holes, which are loose and oily.
更換合金時,筒內未清理干凈;
When the alloy is replaced, the inside of the cylinder is not cleaned.
擠壓筒溫度和擠壓鑄錠溫度過高;
The temperature of the extruding tube and the temperature of the extruded ingot are too high.
鑄錠溫度、尺寸超過允許負偏差;
The ingot temperature and size exceed the allowable negative deviation.
鑄錠過長,填充太快,鑄錠溫度不均,引起非鼓形填充,因而筒內排氣不完全,或操作不當,未執行排氣工序;
The ingots are too long, the filling is too fast, and the temperature of the ingot is uneven, resulting in non drum shaped filling, so the exhaust is incomplete or improper in the cylinder, and the exhaust process is not carried out.
模孔設計不合理,或切殘料不當,分流孔和導流孔中的殘料被部分帶出,擠壓時空隙中的氣體進入表面。
The design of the mold hole is unreasonable, or the cutting residual material is not proper. The residual material in the diverting hole and the diversion hole is partly taken out, and the gas in the space time gap is extruded into the surface.

鋁板生產廠家
二、鋁板擠壓產生氣泡、起皮的消除方法
Two. Methods to eliminate bubbles and skins from aluminum extrusion.
合理設計擠壓筒和擠壓墊片的配合尺寸,經常檢查工具尺寸,保證符合要求,擠壓筒出現大肚要及時修理,擠壓墊不能超差;
Reasonable design of the matching dimensions of the extruding and extruding gaskets, often check the size of the tool, guarantee the requirements, the extrusion cylinder should be repaired in time, and the extruding pad can not be overtaken.
工具、鑄錠表面保持清潔、光滑和干燥;
The surface of tools and ingots should be clean, smooth and dry.
更換合金時,徹底清筒;
When replacing the alloy, clean the tube thoroughly.
經常檢查設備和儀器,防止溫度過高、速度過快;
Check equipment and instruments regularly to prevent high temperature and speed.
嚴格執行工藝規程和各項制度;
Strictly implement the process regulations and various systems.
合理設計、制造工模具,導流孔和分流孔設計成1°-3°內斜度;
Reasonable design and manufacture of tooling, diversion holes and diversion holes are designed to be 1 degrees -3 degrees.
嚴格操作,正確剪切殘料和完全排氣。
Strict operation, correct cutting of debris and complete exhaust.

主站蜘蛛池模板: 香港三级精品三级在线专区| 亚洲 欧美 国产 制服 动漫| 女同性av片在线观看免费网站 | 国产无遮挡又爽又刺激的视频老师| 吸咬奶头狂揉60分钟视频| 精品久久久久久无码专区不卡| 亚洲av鲁丝一区二区三区黄 | 九九精品成人免费国产片| 无码人妻一区二区三区免费视频 | 国产麻无矿码直接进入| 巨爆中文字幕巨爆区爆乳| 亚洲国产成人片在线观看无码| 成年免费a级毛片免费看| 欧洲熟妇色xxxx欧美老妇| 午夜久久久久久禁播电影| 青青青草国产线观| 亚洲成a人v欧美综合天堂| 色噜噜狠狠狠狠色综合久一| 超碰最新上传| 免费看少妇作爱视频| 亚洲一区二区三区国产精华液| 国产白嫩漂亮美女在线观看 | 无码人妻少妇色欲av一区二区| 女人18毛片a级毛片| 国产精品无码dvd在线观看| 久久久久久国产精品无码超碰动画| 国产在线视频一区二区三区| 久久亚洲精品ab无码播放| 狠狠色噜噜狠狠狠狠888奇禾 | 中文字幕av无码不卡免费| 蜜臀av一区二区| 精品国产欧美一区二区| 国产精品va无码二区| 久久精品亚洲男人的天堂| 又粗又硬又大又爽免费视频播放| 国产av旡码专区亚洲av苍井空 | 亚洲av综合色区无码专区桃色| 亚洲成av人片在线观看无码| 国产av一区二区三区无码野战| 久久久亚洲欧洲日产国码农村| 久久久精品456亚洲影院|