日本h番全彩无遮挡h工口-国产精品无码无片在线观看3d-四虎国产成人永久精品免费-广东少妇大战黑人34厘米视频-人人妻人人狠人人爽天天综合网

當前位置:首頁-新聞資訊

鋁板折彎后開裂的主要原因及注意事項

來源:http://www.kangyanghua.com/ 發布時間:2020-08-24

使鋁板折彎后開裂的幾個主要原因及注意事項:
Several main reasons and precautions for cracking of aluminum plate after bending are as follows:
1、鋁板的硬度
   1. Hardness of aluminum plate
鋁板硬度太高,很容易開裂。這就需求挑選質量好的鋁板,主要看鋁板合金和狀態。通常1系列、3系列、5系列的對比常用,6系列、7系列的硬度太高,要先做退火處理到O態后才好折彎。還有即是鋁板的質量。
   aluminum plate has too high hardness and is easy to crack. This requires the selection of good quality aluminum plate, mainly depends on the aluminum plate alloy and state. Generally, the comparison of 1 series, 3 series and 5 series is commonly used. The hardness of 6 series and 7 series is too high, so it is necessary to conduct annealing treatment to o state before bending. There is also the quality of aluminum plate.
2、鋁板的厚度。
   2. Thickness of aluminum plate.
太厚的鋁板不好折彎,我們一想就理解,盡量運用薄一點的鋁板。
                     .
3、折彎R角的巨細
   3. The size of bending R angle
折彎R角越大,那成功率就越高,所以盡量調大折彎R角越大。
   the larger the bending R angle, the higher the success rate, so try to increase the bending R angle to increase the greater.
4、鋁板紋理方向。


折彎方向要與鋁板紋理方向垂直,不能平行。
   the bending direction should be perpendicular to the grain direction of aluminum plate, not parallel.
需求拉絲的鋁板零件,在工序答應的情況下佳是折彎后再拉形,否則會添加折彎開裂的概率。
   for aluminum plate parts requiring wire drawing, the best way is to stretch after bending when the process is allowed, otherwise the probability of bending cracking will be added.
鋁板生產廠家
Aluminum plate manufacturer
是狀態重要了
  first of all, state matters
狀態分為全硬、半硬、軟態(通常軟態叫O態),全硬的折彎效果基本不太行(鋁板狀態是H18、H19、H38等都是全硬的),半硬狀態的鋁板基本上都可以折彎(H24的也就是半硬的)。O態的折彎是肯定沒問題,但是由于太軟了,基本上用這種狀態的來折彎的比較少。
   state is divided into full hard, semi-hard and soft state (usually soft state is called o state). The bending effect of full hard is not very good (aluminum plate state is h18, H19, h38, etc.) and aluminum plate in semi-hard state can be basically bent (H24 is semi-hard). O-state bending is certainly no problem, but because it is too soft, basically using this state to bend less.
其次是你要選擇純鋁還是合金鋁
   next, do you want pure aluminum or alloy aluminum
純鋁硬度不是很高,用1100、1050、1060等等都可以,推薦用1100  H26的合金鋁硬度好一點,可以用3003、3005、5052等半硬狀態的都可以的。
   the hardness of pure aluminum is not very high. 1100, 1050, 1060 and so on can be used. It is recommended to use 1100 H26 alloy with better hardness, and 3003, 3005, 5052 and other semi hard states can be used.
具體情況建議試樣再確定,如果用6061、2024、7075由于硬度太高,特別是T6狀態的更是,應該折彎不了,除非加溫再折,質量好的鋁板與質量差鋁板的區別是氧化性能、公差、表面效果、晶精度及均勻穩定性等有區別的,單單折彎效果區別不大。
    it is suggested to re determine the sample. If 6061, 2024 and 7075 are used, the hardness is too high, especially for T6 state, it should not be bent. Unless the aluminum plate with good quality is re folded after heating, the difference between good quality aluminum plate and poor quality aluminum plate is oxidation performance, tolerance, surface effect, crystal precision and uniform stability, but the bending effect is not different.

主站蜘蛛池模板: 夜夜爽77777妓女免费看| 欧美一性一乱一交一视频| 亚洲永久无码7777kkk| 久久久久久久女国产乱让韩| 乱人伦xxxx国语对白| 日本夜爽爽一区二区三区| 久久久国产成人一区二区 | 97人人添人澡人人爽超碰| 全国最大成人网| 新妺妺窝人体色www| 免费无码一区二区三区蜜桃大| 国产精品无码一区二区在线观一| 黑人教练与人妻小茹阅读| 欧美 国产 综合 欧美 视频| 亚洲国产精品嫩草影院| 人妻少妇精品视频专区| 妺妺窝人体色www看美女| 日韩乱码人妻无码中文字幕| 久久精品欧美日韩精品| 久久99精品久久久大学生 | 亚洲av日韩av激情亚洲| 精品国模一区二区三区| 国模吧双双大尺度炮交gogo| 少妇厨房愉情理伦片视频在线观看 | 成人午夜高潮a∨猛片| 去干成人网| 国产精品久久久久久吹潮| 久久人妻av无码中文专区| 性高湖久久久久久久久| 亚洲av高清在线观看一区二区三区 | 人妻丰满熟妇岳av无码区hd| 三年片在线观看大全国语| 国产精品国产三级国产普通话| 口述他用舌头给我添高潮| 亚洲国产欧美国产综合一区| 网禁拗女稀缺资源在线观看| 欧美乱妇狂野欧美在线视频| 亚洲av综合色区无码一二三区| 芒果乱码国色天香| 国产精品99久久久久久宅男| 精品国产一二三产品价格|