日本h番全彩无遮挡h工口-国产精品无码无片在线观看3d-四虎国产成人永久精品免费-广东少妇大战黑人34厘米视频-人人妻人人狠人人爽天天综合网

當前位置:首頁-新聞資訊

鋁板的擠壓過程表面起泡是由什么原因造成的?

來源:http://www.kangyanghua.com/ 發布時間:2020-12-22

在鋁板的擠壓過程中,很容會出現表面起皮或氣泡,到底是什么原因造成的呢?該用什么方法來消除呢?現在就由鋁板生產廠家為您排異解惑吧!
In the process of aluminum plate extrusion, it is easy to appear surface peeling or bubbles. What is the reason? How to eliminate it? Now let the aluminum plate manufacturer solve the problem for you!
什么是氣泡或起皮:在制品表面出現凸形的泡,常見于頭、尾部,完整的叫氣泡,已破裂的叫起皮。
What is bubble or flaking: convex bubble appears on the surface of the product, common in the head and tail, complete called bubble, has broken called peeling.
一、鋁板擠壓產生氣泡、起皮的原因
1、 Causes of air bubble and peeling during extrusion of aluminum plate
1.擠壓筒、擠壓墊磨損超差,擠壓筒和擠壓墊尺寸配合不當,使用的墊片直徑差超過允許值;
1. The wear of extrusion cylinder and cushion is out of tolerance, the size of extrusion cylinder and extrusion pad is not matched properly, and the diameter difference of gasket used exceeds the allowable value;
2.擠壓筒和擠壓墊太臟,粘有油污、水分、石墨等;
2. The extrusion cylinder and pad are too dirty, with oil, moisture, graphite, etc;

 


3.潤滑油中含有水;
3. The lubricating oil contains water;
4.鑄錠表面鏟槽太多,過深,或鑄錠表面有氣孔、砂眼,組織疏松、有油污等;
4. There are too many grooves on the surface of the ingot, which are too deep, or there are pores and sand holes on the surface of the ingot, and the structure is loose and greasy;
5.更換合金時,筒內未清理干凈;
5. The cylinder is not cleaned when the alloy is replaced;
6.擠壓筒溫度和擠壓鑄錠溫度過高;
6. The temperature of extrusion cylinder and ingot is too high;
7.鑄錠溫度、尺寸超過允許負偏差;
7. The ingot temperature and size exceed the allowable negative deviation;
8.鑄錠過長,填充太快,鑄錠溫度不均,引起非鼓形填充,因而筒內排氣不完全,或操作不當,未執行排氣工序;
8. Too long ingot, too fast filling, uneven ingot temperature, resulting in non drum filling, so that the exhaust in the cylinder is not complete, or improper operation, and the exhaust process is not carried out;
9.模孔設計不合理,或切殘料不當,分流孔和導流孔中的殘料被部分帶出,擠壓時空隙中的氣體進入表面。
9. The design of die hole is unreasonable, or the cutting of scrap is improper. The residual material in the diversion hole and diversion hole is partially carried out, and the gas in the space gap enters the surface during extrusion.
二、鋁板擠壓產生氣泡、起皮的消除方法
2、 Elimination of air bubble and peeling during extrusion of aluminum plate
1.合理設計擠壓筒和擠壓墊片的配合尺寸,經常檢查工具尺寸,保證符合要求,擠壓筒出現大肚要及時修理,擠壓墊不能超差;
1. Reasonably design the matching size of the extrusion cylinder and the extrusion gasket, check the tool size regularly to ensure that they meet the requirements, repair the big belly of the extrusion cylinder in time, and the extrusion pad shall not exceed the tolerance;
2.工具、鑄錠表面保持清潔、光滑和干燥;
2. Keep the surface of tools and ingots clean, smooth and dry;
3.更換合金時,徹底清筒;
3. Clean the cylinder thoroughly when replacing the alloy;
4.經常檢查設備和儀器,防止溫度過高、速度過快;
4. Check the equipment and instruments frequently to prevent the temperature from being too high and the speed too fast;
5.嚴格執行工藝規程和各項制度;
5. Strictly implement the process procedures and systems;
6.合理設計、制造工模具,導流孔和分流孔設計成1°-3°內斜度;嚴格操作,正確剪切殘料和完全排氣。
6. Reasonable design and manufacture of tools and moulds, the diversion hole and the diversion hole should be designed with an internal slope of 1 ° to 3 ° and the operation should be strictly carried out to cut the residual materials correctly and exhaust completely.
通過專家的答疑解惑,相信大家對鋁板擠壓產生氣泡、起皮的原因及消除方法都有了深刻的了解,在日常生產中避免這些問題,就能減少損耗,提高成品率。
Through the expert's question and answer, I believe everyone has a deep understanding of the causes and elimination methods of bubbles and peeling in aluminum plate extrusion. If we avoid these problems in daily production, we can reduce the loss and improve the yield.

主站蜘蛛池模板: 亚洲2022国产成人精品无码区| 久久久久99精品成人片牛牛影视 | 蜜桃麻豆www久久囤产精品| 色五月丁香五月综合五月| 国产精一品亚洲二区在线播放| 999久久久精品国产消防器材 | 人人超碰人人爱超碰国产| 人妻少妇一区二区三区| 国产成人综合在线视频| 又粗又黑又大的吊av| 亚洲无线码一区二区三区| 国产精品自在线拍国产| 宅男666在线永久免费观看 | 性欧美丰满熟妇xxxx性| 国产日产精品久久久久快鸭| 色婷婷综合和线在线| 色噜噜一区二区三区| av无码免费永久在线观看| 无码国产精品一区二区免费式影视| 国产盗摄xxxx视频xxxx| 国产精品99久久免费| 小说区 亚洲 自拍 另类| 女性裸体啪啪无遮挡动态图| 亚洲中文字幕一区精品自拍 | 99无码熟妇丰满人妻啪啪| 久久99精品久久久久久噜噜| 午夜福利1000集合集92| 亚洲国产精品久久久久婷婷老年 | 欧美日韩亚洲精品瑜伽裤| 无遮挡啪啪摇乳动态图| 久99久热只有精品国产女同| 欧美交a欧美精品喷水| 在线看片免费人成视久网| 人妻体体内射精一区二区| 日韩精品久久久久久久电影蜜臀| 怡红院av一区二区三区| 国产成人精品免费久久久久| 性色av无码不卡中文字幕| 国产精品久久久久影院嫩草| 国产精品vⅰdeoxxxx国产| 亲近乱子伦免费视频|