日本h番全彩无遮挡h工口-国产精品无码无片在线观看3d-四虎国产成人永久精品免费-广东少妇大战黑人34厘米视频-人人妻人人狠人人爽天天综合网

當前位置:首頁-新聞資訊

影響鋁板平直度的因素有哪些?

來源:http://www.kangyanghua.com/ 發布時間:2021-03-23

(1)鉗口夾持質量對5052鋁板拉伸品質起著決定性的作用,鉗口的均勻夾持使板材縱向每一個單元都被拉伸到等量長度,從而實現均勻拉伸,起到了對板材的矯直作用。
(1) The clamping quality of the jaw plays a decisive role in the tensile quality of 5052 aluminum plate. The uniform clamping of the jaw makes each unit of the plate be stretched to the same length in the longitudinal direction, so as to realize the uniform stretching and straighten the plate.
(2)拉伸機機架的剛度與預變形補償?shù)挠绊懀河捎诎宀睦鞕C(jī)的兩個拉力缸  等量安置在兩側,對于橫截面越大的板材,在拉伸過程中機架產生的變形也越大。因此,拉伸機機架應保持更大的剛度,設計與制造中應考慮機架預變形償,以克服和補償拉伸過程中機架產生的變形。
(2) Influence of frame stiffness and pre deformation compensation: because the two tension cylinders of the plate drawing machine are equally placed on both sides, the larger the cross section of the plate, the greater the deformation of the frame during the drawing process. Therefore, the frame of the drawing machine should maintain greater stiffness, and the pre deformation compensation of the frame should be considered in the design and manufacture, so as to overcome and compensate the deformation of the frame during the drawing process.


(3)拉伸前5052鋁板板材尺寸的不規則性和應力分布的不均勻性,拉伸過程中有效地控制平穩的速度,使各個變形單元得以充分均勻地變形,是滿足均勻拉伸的重要
(3) Before drawing, the size of 5052 aluminum plate is irregular and the stress distribution is non-uniform. In the drawing process, it is important to control the smooth speed effectively so that each deformation unit can deform fully and evenly
(4)實踐證明,長度相對小一些,寬度相對大一些的板材,其橫向展平效果  條件之一要好得多。生產中應選擇寬、長比大一些的工藝方案。
(4) Practice has proved that the transverse flattening effect of plates with relatively small length and large width is much better. In the production, the process plan with larger ratio of width to length should be selected.
(5)對淬火后變形較大的板材,應利用輥式矯直機初步矯平,而后在拉伸機上進行終的精矯平。
(5) For the plate with large deformation after quenching, the roller straightener should be used for preliminary leveling, and then the final fine leveling should be carried out on the drawing machine.
(6)由于拉伸機的主要作用是消除板材的殘余應力,以縱向小變形量的塑性  變形過程為主,因而對縱向有更好的矯直作用,對橫向平直度的改善能力非常有限。
(6) Because the main function of the drawing machine is to eliminate the residual stress of the plate, the plastic deformation process with small longitudinal deformation is the main process, so it has a better straightening effect on the longitudinal direction, and its ability to improve the transverse flatness is very limited.

主站蜘蛛池模板: 在教室伦流澡到高潮hgl动漫| 国产ww久久久久久久久久| 亚洲性色av私人影院无码| 日韩精品无码一区二区三区免费| 69综合精品国产二区无码| 亚洲国产精品成人午夜在线观看| 国产成人亚洲精品无码车a| 又色又爽又黄又无遮挡网站| 成人免费a级毛片| 日韩中文字幕免费视频| 老熟妇高潮一区二区三区| 久久久受www免费人成| 波多野42部无码喷潮| 精品一区二区三区在线播放视频| 亚洲精品无码av人在线观看国产| 99国内精品久久久久久久| 奇米影视7777狠狠狠狠色| 亚洲熟妇色xxxxx欧美老妇y| 野花社区在线视频最新| 日本午夜精品理论片a级app发布| 少妇午夜啪爽嗷嗷叫视频| 最新国产aⅴ精品无码| 久久久久女教师免费一区| 成人做受视频试看60秒| 亚洲人成电影在线播放| 亚洲综合另类小说专区| 亚洲欧美日韩综合一区| 亚洲а∨精品天堂在线| 欧美熟妇另类久久久久久多毛| 亚洲午夜无码久久| 免费黄色电影在线观看| 中文无码久久精品| 久激情内射婷内射蜜桃人妖| 免费无码av一区二区| 国产三级a三级三级| 久久久精品日本一区二区三区 | 香蕉久久久久久av成人| 无线乱码一二三区免费看| 亚洲av无码一区东京热| 小12箩利洗澡无码视频网站| 亚洲精品白浆高清久久久久久 |