鋁板這些材料具有強烈的時代感和技術感，以及很高的藝術感染力。然而，鋁板的使用還有一些需要注意的方面，那么在使用鋁板時需要注意的事項是什么呢？鋁板生產廠家為您講解。
These materials of aluminum plate have a strong sense of the times and technology, as well as a high artistic appeal. However, there are still some aspects to be paid attention to when using aluminum plates. What are the matters to be paid attention to when using aluminum plates? The aluminum plate manufacturer will explain it to you.
1.鋁板使用條件：內墻板應在室內使用，不應安裝在室外，以保證使用效果和使用壽命。
1. Service conditions of aluminum plate: interior wall plate shall be used indoors, not installed outdoors, to ensure service effect and service life.
2.鋁板安裝方向：當同一色鋁板安裝在同一平面上時，流動方向應相同，否則可能造成視覺色差。
2. Aluminum plate installation direction: When aluminum plates with the same color are installed on the same plane, the flow direction should be the same, otherwise visual color difference may be caused.
3.鋁板的撕裂膜：應在安裝鋁板后45天內將保護膜撕掉，否則可能發生撕膜或移動膠水的困難。
3. Tear film of aluminum plate: tear off the protective film within 45 days after installing the aluminum plate, otherwise it may be difficult to tear the film or move the glue.
4.鋁板批次：同一型號和不同批次的鋼板可能有色差，在銷售和使用不同批次的中厚板時，應增加色差比較的程序。本公司主要經營鋁合金鋁板、鋁板等，在不考慮色差的情況下只能在同一平面上使用。
4. Aluminum plate batch: steel plates of the same model and different batches may have color difference. When selling and using medium and thick plates of different batches, the procedure of color difference comparison shall be added. The company mainly deals in aluminum alloy aluminum plates, aluminum plates, etc., which can only be used on the same plane without considering the color difference.
5.鋁板的貯存和運輸：鋁板應存放在干燥通風的地方，平放在平面上，不得踩踏和撞擊，搬運板應同時抬起板的四面，嚴禁推、拉、拔，以免刮傷板表面。
5. Storage and transportation of aluminum plates.

6.鋁板彎曲邊的圓弧加工：彎曲邊應均勻，一次成型，不要反復彎曲，否則鋁板可能會斷裂，加工電弧應采用特殊的彎曲設備，緩慢作用力，使板材逐漸達到要求的表面。不要一次彎曲。
6. Arc processing of bending edge of aluminum plate: The bending edge shall be uniform, formed at one time, and do not bend repeatedly, otherwise the aluminum plate may break. Special bending equipment shall be used for arc processing, and the force shall be applied slowly to make the plate gradually reach the required surface. Do not bend at once.
7.鋁板開槽：當開槽機或鑼機用于開槽時，應使用大于90度的半圓頭銑刀。刀不應對鋁板造成太深的傷害，也不應使邊緣難以折疊。0-0.3mm厚的塑料芯應與鋁板一起彎曲，以提高強度和韌性，否則鋁板可能會斷裂，或在邊緣彎曲時油漆膜會破裂。
7. Aluminum plate slotting: When the slotting machine or gong machine is used for slotting, a semicircle head milling cutter greater than 90 degrees shall be used. The knife shall not cause too deep damage to the aluminum plate, nor make the edge difficult to fold. The 0-0.3mm thick plastic core shall be bent together with the aluminum plate to improve the strength and toughness, otherwise the aluminum plate may break, or the paint film may break when the edge is bent.
鋁板表面使用中應注意的事項基礎上就是這些內容了，您對此有什么想咨詢的問題或者有需求嗎？歡迎來我們網站http://www.kangyanghua.com進行咨詢了解！
This is the basis for the precautions in the use of aluminum plate surface. Do you have any questions or needs? Welcome to our website http://www.kangyanghua.com Ask about it!